Recent advances in microplastic removal from drinking water by coagulation: Removal mechanisms and influencing factors.

Microplastics (MPs) are emerging contaminants that are widely detected in drinking water and pose a potential risk to humans. Therefore, the MP removal from drinking water is a critical challenge. Recent studies have shown that MPs can be removed by coagulation. However, the coagulation removal of MPs from drinking water remains inadequately understood. Herein, the efficiency, mechanisms, and influencing factors of coagulation for removing MPs from drinking water are critically reviewed. First, the efficiency of MP removal by coagulation in drinking water treatment plants (DWTPs) and laboratories was comprehensively summarized, which indicated that coagulation plays an important role in MP removal from drinking water. The difference in removal effectiveness between the DWTPs and laboratory was mainly due to variations in treatment conditions and limitations of the detection techniques. Several dominant coagulation mechanisms for removing MPs and their research methods are thoroughly discussed. Charge neutralization is more relevant for small-sized MPs, whereas large-sized MPs are more dependent on adsorption bridging and sweeping. Furthermore, the factors influencing the efficiency of MP removal were jointly analyzed using meta-analysis and a random forest model. The meta-analysis was used to quantify the individual effects of each factor on coagulation removal efficiency by performing subgroup analysis. The random forest model quantified the relative importance of the influencing factors on removal efficiency, the results of which were ordered as follows: MPs shape > Coagulant type > Coagulant dosage > MPs concentration > MPs size > MPs type > pH. Finally, knowledge gaps and potential future directions are proposed. This review assists in the understanding of the coagulation removal of MPs, and provides novel insight into the challenges posed by MPs in drinking water.

The aging behavior of degradable plastic polylactic acid under the interaction of environmental factors.

Microplastics leaching from aging biodegradable plastics pose potential environmental threats. This study used response surface methodology (RSM) to investigate the impact of temperature, light, and humidity on the aging characteristics of polylactic acid (PLA). Key evaluation metrics included the C/O ratio, functional groups, crystallinity, surface topography, and mechanical properties. Humidity was discovered to have the greatest effect on the ageing of PLA, followed by light and temperature. The interactions between temperature and light, as well as humidity and sunlight, significantly impact the aging of PLA. XPS analysis revealed PLA underwent aging due to the cleavage of the ester bond (O-C=O), resulting in the addition of C=O and C-O. The aging process of PLA was characterized by alterations in surface morphology and augmentation in crystallinity, resulting in a decline in both tensile strength and elongation. These findings might offer insights into the aging behavior of degradable plastics under diverse environmental conditions.

Repeated Exposure Enhanced Toxicity of Clarithromycin on Microcystis aeruginosa Versus Single Exposure through Photosynthesis, Oxidative Stress, and Energy Metabolism Shift.

Antibiotics are being increasingly detected in aquatic environments, and their potential ecological risk is of great concern. However, most antibiotic toxicity studies involve single-exposure experiments. Herein, we studied the effects and mechanisms of repeated versus single clarithromycin (CLA) exposure on Microcystis aeruginosa. The 96 h effective concentration of CLA was 13.37 µg/L upon single exposure but it reduced to 6.90 µg/L upon repeated exposure. Single-exposure CLA inhibited algal photosynthesis by disrupting energy absorption, dissipation and trapping, reaction center activation, and electron transport, thereby inducing oxidative stress and ultrastructural damage. In addition, CLA upregulated glycolysis, pyruvate metabolism, and the tricarboxylic acid cycle. Repeated exposure caused stronger inhibition of algal growth via altering photosynthetic pigments, reaction center subunits biosynthesis, and electron transport, thereby inducing more substantial oxidative damage. Furthermore, repeated exposure reduced carbohydrate utilization by blocking the pentose phosphate pathway, consequently altering the characteristics of extracellular polymeric substances and eventually impairing the defense mechanisms of M. aeruginosa. Risk quotients calculated from repeated exposure were higher than 1, indicating significant ecological risks. This study elucidated the strong influence of repeated antibiotic exposure on algae, providing new insight into antibiotic risk assessment.

CS/CoFe2O4 nanocomposite as a high-effective and steady chainmail catalyst for tetracycline degradation with peroxymonosulfate activation: performance and mechanism.

Tetracycline becomes a crucial measure for managing and treating communicable diseases in both human and animal sectors due to its beneficial antibacterial properties and cost-effectiveness. However, it is important not to trivialize the associated concerns of environmental contamination following the antibiotic's application. In this study, cobalt ferrate (CoFe2O4) nanoparticles were loaded into chitosan (CS), which can avoid the agglomeration problem caused by high surface energy and thus improve the catalytic performance of cobalt ferrate. And it can avoid the problem of secondary contamination caused by the massive leaching of metal ions. The resulting product was used as a catalyst to activate peroxymonosulfate (PMS) for the degradation of tetracycline (TC). To determine the potential effects on TC degradation, various factors such as PMS dosing, catalyst dosing, TC concentration, initial solution pH, temperature, and inorganic anions (Cl-, H2PO4- and HCO3-) were investigated. The CS/CoFe2O4/PMS system exhibited superior performance compared to the CoFe2O4-catalyzed PMS system alone, achieving a 92.75% TC removal within 120 min. The catalyst displayed high stability during the recycling process, with the efficiency observed after five uses remaining at a stable 73.1%, and only minor leaching of dissolved metal ions from the catalyst. This confirms the high stability of the catalyst. The activation mechanism study showed that there are free radical and non-free radical pathways in the reaction system to degrade TC together, and SO4•- and 1O2 are the primary reactive oxygen radicals involved in the reaction, allowing for effective treatment of contaminated water by TC.

Organic Phosphorescent Hopper-Shaped Microstructures.

Hopper-shaped microcrystals, an unusual type of crystal with a large specific surface area, are promising for use in catalysis, drug delivery, and gas sensors. In contrast to well-studied inorganic hopper-shaped crystals, organic phosphorescent concave hopper-shaped microstructures are rarely reported. This study reports the synthesis of two types of organic stepped indented hopper-shaped microstructures with efficient room temperature phosphorescence (RTP) using a liquid phase self-assembly strategy. The formation mechanism is attributed to the interfacial instability induced by the concentration gradient and selective etching. Compared with flat microstructures, the stepped indented hopper-like RTP microstructures exhibit high sensitivity to oxygen. This work also demonstrates that packing the photochromic material into the concave hopper "vessel" effectively controls the switch of phosphorescence from energy transfer, expanding the potential applications of phosphorescent materials.

Magnesium Hydroxide as a Versatile Nanofiller for 3D-Printed PLA Bone Scaffolds.

Polylactic acid (PLA) has attracted much attention in bone tissue engineering due to its good biocompatibility and processability, but it still faces problems such as a slow degradation rate, acidic degradation product, weak biomineralization ability, and poor cell response, which limits its wider application in developing bone scaffolds. In this study, Mg(OH)2 nanoparticles were employed as a versatile nanofiller for developing PLA/Mg(OH)2 composite bone scaffolds using fused deposition modeling (FDM) 3D printing technology, and its mechanical, degradation, and biological properties were evaluated. The mechanical tests revealed that a 5 wt% addition of Mg(OH)2 improved the tensile and compressive strengths of the PLA scaffold by 20.50% and 63.97%, respectively. The soaking experiment in phosphate buffered solution (PBS) revealed that the alkaline degradation products of Mg(OH)2 neutralized the acidic degradation products of PLA, thus accelerating the degradation of PLA. The weight loss rate of the PLA/20Mg(OH)2 scaffold (15.40%) was significantly higher than that of PLA (0.15%) on day 28. Meanwhile, the composite scaffolds showed long-term Mg2+ release for more than 28 days. The simulated body fluid (SBF) immersion experiment indicated that Mg(OH)2 promoted the deposition of apatite and improved the biomineralization of PLA scaffolds. The cell culture of bone marrow mesenchymal stem cells (BMSCs) indicated that adding 5 wt% Mg(OH)2 effectively improved cell responses, including adhesion, proliferation, and osteogenic differentiation, due to the release of Mg2+. This study suggests that Mg(OH)2 can simultaneously address various issues related to polymer scaffolds, including degradation, mechanical properties, and cell interaction, having promising applications in tissue engineering.

Ground-State Orbital Descriptors for Accelerated Development of Organic Room-Temperature Phosphorescent Materials.

Organic materials with room-temperature phosphorescence (RTP) are in high demand for optoelectronics and bioelectronics. Developing RTP materials highly relies on expert experience and costly excited-state calculations. It is a challenge to find a tool for effectively screening RTP materials. Herein we first establish ground-state orbital descriptors (πFMOs ) derived from the π-electron component of the frontier molecular orbitals to characterize the RTP lifetime (τp ), achieving a balance in screening efficiency and accuracy. Using the πFMOs , a data-driven machine learning model gains a high accuracy in classifying long τp , filtering out 836 candidates with long-lived RTP from a virtual library of 19,295 molecules. With the aid of the excited-state calculations, 287 compounds are predicted with high RTP efficiency. Impressively, experiments further confirm the reliability of this workflow, opening a novel avenue for designing high-performance RTP materials for potential applications.

Adsorption and aggregation of Cu2+ on carboxymethylated sugarcane bagasse: Adsorption behavior and mechanism.

Abundant biomass resources provide us with sufficient material basis, while a large amount of bio-waste is also produced and the high-value utilization of bio-waste is still highly desirable. Herein, we reported a facile one-pot fabrication approach towards efficient utilization of sugarcane bagasse via carboxymethylation to adsorb and recycle Cu2+ ions. The modified sugarcane bagasse possessed outstanding adsorption efficiency, with a maximum capacity of 263.7 mg g-1, owing to the functional groups such as carboxyl and hydroxyl groups, as well as aromatic structure. It was noted that the carboxymethylated sugarcane bagasse (MSB40) swelled rapidly when suffering Cu2+ ions solution, and more adsorption sites were available since the physical diffusion barrier was removed, thereby enhancing the absorption capacity. Interestingly, Cu2+ ions could induce the aggregation of MSB40 due to the Cu2+ ions compress colloid double layer, neutralizes surface charges, which benefited the following separation process. Ultimately, copper oxide was recovered and the purity reached 97.9%. Additionally, in the presence of both Ca2+ and Mg2+ ions, MSB40 exhibited excellent selectivity for the adsorption of Cu2+ ions. This strategy offers a facile and novel clue for the high-value utilization of bio-waste and the recovery of copper for biomaterial and environmental applications.

Enhanced interfacial boiling of impacting droplets upon vibratory surfaces.

HYPOTHESIS: Despite the flourishing studies of droplet interfacial boiling, the boiling upon vibratory surfaces, which may cause vigorous liquid-vapor-solid interactions, has rarely been investigated. Enhanced boiling normally can be gained from rapid removal of vapor and disturbance of liquid-vapor interface. We hypothesize that the vibratory surfaces enhance both effects with new intriguing phenomena and thus, attain an enhanced boiling heat transfer. EXPERIMENTS: We experimentally investigated the impacting fluid dynamics and coupled heat transfer patterns of multiple droplets and a single droplet impinging on still and vibratory surfaces of various materials and different wettability. FINDINGS: The boiling under vibratory surfaces with increased vibration velocity amplitude and enhanced wettability can be enhanced by 80% in heat transfer coefficient and Nusselt number, which is attributed to several reasons: shortened bubble lifespan, thinner and smaller bubbles, and enhanced disturbances in liquid-vapor interfaces. The vibration also delays the Leidenfrost point when the droplet impacts a descending surface, which shows that the droplet impact moment (vibration phase angle) is particularly crucial. The descending surface releases the generated vapor actively and facilitates liquid-solid contact, thereby delaying the Leidenfrost. From fundamentals to application, this article strengthens our understanding of vibrated interfacial boiling in scenarios closer to multiple natural processes and practical industries.

Repurposing conformational changes in ANL superfamily enzymes to rapidly generate biosensors for organic and amino acids.

Biosensors are powerful tools for detecting, real-time imaging, and quantifying molecules, but rapidly constructing diverse genetically encoded biosensors remains challenging. Here, we report a method to rapidly convert enzymes into genetically encoded circularly permuted fluorescent protein-based indicators to detect organic acids (GECFINDER). ANL superfamily enzymes undergo hinge-mediated ligand-coupling domain movement during catalysis. We introduce a circularly permuted fluorescent protein into enzymes hinges, converting ligand-induced conformational changes into significant fluorescence signal changes. We obtain 11 GECFINDERs for detecting phenylalanine, glutamic acid and other acids. GECFINDER-Phe3 and GECFINDER-Glu can efficiently and accurately quantify target molecules in biological samples in vitro. This method simplifies amino acid quantification without requiring complex equipment, potentially serving as point-of-care testing tools for clinical applications in low-resource environments. We also develop a GECFINDER-enabled droplet-based microfluidic high-throughput screening method for obtaining high-yield industrial strains. Our method provides a foundation for using enzymes as untapped blueprint resources for biosensor design, creation, and application.

Insight into the phylogeny and metabolic divergence of Monascus species (M. pilosus, M. ruber, and M. purpureus) at the genome level.

Background: Species of the genus Monascus are economically important and widely used in the production of food colorants and monacolin K. However, they have also been known to produce the mycotoxin citrinin. Currently, taxonomic knowledge of this species at the genome level is insufficient. Methods: This study presents genomic similarity analyses through the analysis of the average nucleic acid identity of the genomic sequence and the whole genome alignment. Subsequently, the study constructed a pangenome of Monascus by reannotating all the genomes and identifying a total of 9,539 orthologous gene families. Two phylogenetic trees were constructed based on 4,589 single copy orthologous protein sequences and all the 5,565 orthologous proteins, respectively. In addition, carbohydrate active enzymes, secretome, allergic proteins, as well as secondary metabolite gene clusters were compared among the included 15 Monascus strains. Results: The results clearly revealed a high homology between M. pilosus and M. ruber, and their distant relationship with M. purpureus. Accordingly, all the included 15 Monascus strains should be classified into two distinctly evolutionary clades, namely the M. purpureus clade and the M. pilosus-M. ruber clade. Moreover, gene ontology enrichment showed that the M. pilosus-M. ruber clade had more orthologous genes involved with environmental adaptation than the M. purpureus clade. Compared to Aspergillus oryzae, all the Monascus species had a substantial gene loss of carbohydrate active enzymes. Potential allergenic and fungal virulence factor proteins were also found in the secretome of Monascus. Furthermore, this study identified the pigment synthesis gene clusters present in all included genomes, but with multiple nonessential genes inserted in the gene cluster of M. pilosus and M. ruber compared to M. purpureus. The citrinin gene cluster was found to be intact and highly conserved only among M. purpureus genomes. The monacolin K gene cluster was found only in the genomes of M. pilosus and M. ruber, but the sequence was more conserved in M. ruber. Conclusion: This study provides a paradigm for phylogenetic analysis of the genus Monascus, and it is believed that this report will lead to a better understanding of these food microorganisms in terms of classification, metabolic differentiation, and safety.

Designing gene manipulation schedules for high throughput parallel construction of objective strains.

Recent advances in biofoundries have enabled the construction of a large quantity of strains in parallel, accelerating the design-build-test-learn (DBTL) cycles for strain development. However, the construction of a large number of strains by iterative gene manipulation is still time-consuming and costly, posing a challenge for the development of commercial strains. Common gene manipulations among different objective strains open up the possibility of reducing cost and time for strain construction in biofoundries by optimizing genetic manipulation schedules. A method is introduced consisting of two complementary algorithms for designing optimal parent-children manipulation schedules for strain construction: greedy search of common ancestor strains (GSCAS) and minimizing total manipulations (MTM). By reusing common ancestor strains, the number of strains to be constructed can be effectively reduced, resulting in a tree-like structure of descendants instead of linear lineages for each strain. The GSCAS algorithm can quickly find common ancestor strains and clusters them together based on their genetic makeup, and the MTM algorithm subsequently minimize the genetic manipulations required, resulting in a further reduction in the total number of genetic manipulations. The effectiveness of our method is demonstrated through a case study of 94 target strains, where GSCAS reduces an average of 36% of the total gene manipulations, and MTM reduces an additional 10%. The performance of both algorithms is robust among case studies with different average occurrences of gene manipulations across objective strains. Our method potentially improves cost efficiency and accelerate the development of commercial strains significantly. The implementation of the methods can be freely accessed via https://gscas-mtm.biodesign.ac.cn/.

A combined network pharmacology and molecular biology approach to investigate the potential mechanisms of G-M6 on ovarian cancer.

Ginsenoside 3ß,12ß,21α,22ß-Hydroxy-24-norolean-12-ene (G-M6), a phase I metabolite of anti-tumor medication 20(R)-25-methoxyl-dammarane-3ß,12ß,20-triol (AD-1), beats the parent drug in anti-ovarian cancer efficacy. The mechanism of action for ovarian cancer, however, is uncertain. Using network pharmacology, human ovarian cancer cells and nude mouse ovarian cancer xenotransplantation model, the anti-ovarian cancer mechanism of G-M6 was preliminarily explored in this study. The PPAR signal pathway is the key signal pathway of the G-M6 anti-ovarian cancer mechanism, according to data mining and network analysis. Docking tests demonstrated that the bioactive chemical G-M6 was capable of forming a stable bond with the PPARγ target protein capsule. Using human ovarian cancer cells and xenograft model of ovarian cancer to evaluate the anticancer activity of G-M6. The IC50 value of G-M6 was 5.83±0.36, lower than AD-1 and Gemcitabine. The tumor weight of the RSG 80 mg/kg group (C), G-M6 80 mg/kg group (I), and RSG 80 mg/kg + G-M6 80 mg/kg group (J) after the intervention was as follows: C < I < J. The tumor inhibition rates of groups C, I, and J were 28.6%, 88.7%, and 92.6%, respectively. When RSG and G-M6 are combined to treat ovarian cancer, q = 1.00 is calculated according to King's formula, which indicates that RSG and G-M6 have additive effects. Its molecular mechanism may involve the up-regulation of PPARγ and Bcl-2 protein expressions, and the down-regulation of Bax, Cytochrome C (Cyt. C), Caspase-3, and Caspase-9 protein expressions. These findings serve as a reference for further research into the processes behind ginsenoside G-M6's ovarian cancer therapy.

A natural biomineral for enhancing the biomineralization and cell response of 3D printed polylactic acid bone scaffolds.

Polylactic acid (PLA) has been extensively used as a bone scaffold material, but it still faces many problems including low biomineralization ability, weak cell response, low mechanical properties, etc. In this study, we proposed to utilize the distinctive physical, chemical and biological properties of a natural biomineral with organic matrix, pearl powder, to enhance the overall performance of PLA bone scaffolds. Porous PLA/pearl composite bone scaffolds were prepared using fused deposition modeling (FDM) 3D printing technology, and their comprehensive performance was investigated. Macro- and micro- morphological observation by the optical camera and scanning electron microscopy (SEM) showed the 3D printed scaffolds have interconnected and ordered periodic porous structures. Phase analysis by X-ray diffraction (XRD) indicated pearl powder was well composited with PLA without impurity formation during the melt extrusion process. The mechanical test results indicated the tensile and compressive strength of PLA/pearl composite scaffolds with 10 % pearl powder content yielded the highest values, which were 15.5 % and 21.8% greater than pure PLA, respectively. The water contact angle and water absorption tests indicated that PLA/pearl showed better hydrophilicity than PLA due to the presence of polar groups in the organic matrix of the pearl powder. The results of the simulated body fluid (SBF) soaking revealed that the addition of pearl powder effectively enhanced the formation and deposition of apatite, which was attributed to the release of Ca2+ from the dissolution of pearl powder. The cell culture of bone marrow mesenchymal stem cells (BMSCs) indicated that PLA/pearl scaffolds showed better cell proliferation and osteogenic differentiation than PLA due to the stimulation of the biological organic matrix in pearl powder. These outcomes signify the potential of pearl powder as a natural biomineral containing bio-signal factors to improve the mechanical and biological properties of polymers for better bone tissue engineering application.

Studies on competitive adsorption characteristics of bisphenol A and 17α-ethinylestradiol on thermoplastic polyurethane by site energy distribution theory.

Compound pollution of microplastics and estrogens is a growing ecotoxicological problem in aquatic environments. The adsorption isothermal properties of bisphenol A (BPA) and 17α-ethinyl estradiol (EE2) on polyamide (TPU) in monosolute and bisolute systems were studied. Under the same adsorption concentration (1-4 mg L-1), EE2 had a greater adsorption capacity than BPA in the monsolute system. Compared to the energy distribution features of the adsorption sites of EE2 and BPA, the BPA adsorption sites were located in the higher energy area and were more evenly distributed than those of EE2, while the quantity of BPA adsorption sites was less than that of EE2. In the bisolute system, the average site energy, site energy inhomogeneity, and adsorption site numbers of BPA increased by 1.674, -17.166, and 16.793%, respectively. In comparison, the average site energy, site energy inhomogeneity, and adsorption sites numbers of EE2 increased by 2.267, 4.416, and 8.585%, respectively. The results showed that BPA and EE2 had a cooperative effect on the competitive adsorption of TPU. XPS analysis showed that BPA and EE2 had electron transfer on TPU, although the chemisorption effects and hydrogen bonds between BPA and TPU were more significant. Comparing the changes in the relative functional group content of TPU in monosolute and bisolute systems, BPA and EE2 were synergistically absorbed on TPU. This study can provide a theoretical reference for the study of competitive adsorption between coexisting organic pollutants.

ecBSU1: A Genome-Scale Enzyme-Constrained Model of Bacillus subtilis Based on the ECMpy Workflow.

Genome-scale metabolic models (GEMs) play an important role in the phenotype prediction of microorganisms, and their accuracy can be further improved by integrating other types of biological data such as enzyme concentrations and kinetic coefficients. Enzyme-constrained models (ecModels) have been constructed for several species and were successfully applied to increase the production of commodity chemicals. However, there was still no genome-scale ecModel for the important model organism Bacillus subtilis prior to this study. Here, we integrated enzyme kinetic and proteomic data to construct the first genome-scale ecModel of B. subtilis (ecBSU1) using the ECMpy workflow. We first used ecBSU1 to simulate overflow metabolism and explore the trade-off between biomass yield and enzyme usage efficiency. Next, we simulated the growth rate on eight previously published substrates and found that the simulation results of ecBSU1 were in good agreement with the literature. Finally, we identified target genes that enhance the yield of commodity chemicals using ecBSU1, most of which were consistent with the experimental data, and some of which may be potential novel targets for metabolic engineering. This work demonstrates that the integration of enzymatic constraints is an effective method to improve the performance of GEMs. The ecModel can predict overflow metabolism more precisely and can be used for the identification of target genes to guide the rational design of microbial cell factories.

2D/2D Phosphorus-Doped g-C3N4/Bi2WO6 Direct Z-Scheme Heterojunction Photocatalytic System for Tetracycline Hydrochloride (TC-HCl) Degradation.

Bi2WO6-based heterojunction photocatalyst for antibiotic degradation has been a research hotspot, but its photocatalytic performance needs to be further improved. Therefore, 2D/2D P-doped g-C3N4/Bi2WO6 direct Z-scheme heterojunction photocatalysts with different composition ratios were prepared through three strategies of phosphorus (P) element doping, morphology regulation, and heterojunction, and the efficiency of its degradation of tetracycline hydrochloride (TC-HCl) under visible light was studied. Their structural, optical, and electronic properties were evaluated, and their photocatalytic efficiency for TC-HCl degradation was explored with a detailed assessment of the active species, degradation pathways, and effects of humic acid, different anions and cations, and water sources. The 30% P-doped g-C3N4/Bi2WO6 had the best photocatalytic performance for TC-HCl degradation. Its photocatalytic rate was 4.5-, 2.2-, and 1.9-times greater than that of g-C3N4, P-doped g-C3N4, and Bi2WO6, respectively. The improved photocatalytic efficiency was attributed to the synergistic effect of P doping and 2D/2D direct Z-scheme heterojunction construction. The stability and reusability of the 30% P-doped C3N4/Bi2WO6 were confirmed by cyclic degradation experiments. Radical scavenging experiments and electron spin resonance spectroscopy showed that the main active species were •O2- and h+. This work provides a new strategy for the preparation of direct Z-scheme heterojunction catalysts with high catalytic performance.

Global Cellular Metabolic Rewiring Adapts Corynebacterium glutamicum to Efficient Nonnatural Xylose Utilization.

Xylose, the major component of lignocellulosic biomass, cannot be naturally or efficiently utilized by most microorganisms. Xylose (co)utilization is considered a cornerstone of efficient lignocellulose-based biomanufacturing. We evolved a rapidly xylose-utilizing strain, Cev2-18-5, which showed the highest reported specific growth rate (0.357 h-1) on xylose among plasmid-free Corynebacterium glutamicum strains. A genetically clear chassis strain, CGS15, was correspondingly reconstructed with an efficient glucose-xylose coutilization performance based on comparative genomic analysis and mutation reconstruction. With the introduction of a succinate-producing plasmid, the resulting strain, CGS15-SA1, can efficiently produce 97.1 g/L of succinate with an average productivity of 8.09 g/L/h by simultaneously utilizing glucose and xylose from corn stalk hydrolysate. We further revealed a novel xylose regulatory mechanism mediated by the endogenous transcription factor IpsA with global regulatory effects on C. glutamicum. A synergistic effect on carbon metabolism and energy supply, motivated by three genomic mutations (Psod(C131T)-xylAB, Ptuf(Δ21)-araE, and ipsAC331T), was found to endow C. glutamicum with the efficient xylose utilization and rapid growth phenotype. Overall, this work not only provides promising C. glutamicum chassis strains for a lignocellulosic biorefinery but also enriches the understanding of the xylose regulatory mechanism. IMPORTANCE A novel xylose regulatory mechanism mediated by the transcription factor IpsA was revealed. A synergistic effect on carbon metabolism and energy supply was found to endow C. glutamicum with the efficient xylose utilization and rapid growth phenotype. The new xylose regulatory mechanism enriches the understanding of nonnatural substrate metabolism and encourages exploration new engineering targets for rapid xylose utilization. This work also provides a paradigm to understand and engineer the metabolism of nonnatural renewable substrates for sustainable biomanufacturing.

Construction and Analysis of an Enzyme-Constrained Metabolic Model of Corynebacterium glutamicum.

The genome-scale metabolic model (GEM) is a powerful tool for interpreting and predicting cellular phenotypes under various environmental and genetic perturbations. However, GEM only considers stoichiometric constraints, and the simulated growth and product yield values will show a monotonic linear increase with increasing substrate uptake rate, which deviates from the experimentally measured values. Recently, the integration of enzymatic constraints into stoichiometry-based GEMs was proven to be effective in making novel discoveries and predicting new engineering targets. Here, we present the first genome-scale enzyme-constrained model (ecCGL1) for Corynebacterium glutamicum reconstructed by integrating enzyme kinetic data from various sources using a ECMpy workflow based on the high-quality GEM of C. glutamicum (obtained by modifying the iCW773 model). The enzyme-constrained model improved the prediction of phenotypes and simulated overflow metabolism, while also recapitulating the trade-off between biomass yield and enzyme usage efficiency. Finally, we used the ecCGL1 to identify several gene modification targets for l-lysine production, most of which agree with previously reported genes. This study shows that incorporating enzyme kinetic information into the GEM enhances the cellular phenotypes prediction of C. glutamicum, which can help identify key enzymes and thus provide reliable guidance for metabolic engineering.

Ventilation reconstruction in bathrooms for restraining hazardous plume: Mitigate COVID-19 and beyond.

Converging evidence reports that the probability of vertical transmission patterns via shared drainage systems, may be responsible for the huge contactless community outbreak in high-rise buildings. Publications indicate that a faulty bathroom exhaust fan system is ineffective in removing lifted hazardous virus-laden aerosols from the toilet bowl space. Common strategies (boosting ventilation capability and applying disinfection tablets) seem unsustainable and remain to date untested. Using combined simulation and experimental approaches, we compared three ventilation schemes in a family bathroom including the traditional ceiling fan, floor fan, and side-wall fan. We found that the traditional ceiling fan was barely functional whereby aerosol particles were not being adequately removed. Conversely, a side-wall fan could function efficiently and an enhanced ventilation capability can have increased performance whereby nearly 80.9% of the lifted aerosol particles were removed. There exists a common, and easily-overlooked mistake in the layout of the bathroom, exposing occupants to a contactless vertical pathogen aerosol transmission route. Corrections and dissemination are thus imperative for the reconstruction of these types of family bathrooms. Our findings provide evidence for the bathroom and smart ventilation system upgrade, promoting indoor public health and human hygiene.